BL-1039 Polyurethane foam/密封条组合料
工艺数据表
双组分软质发泡（BL-1039）
混合比率 树脂：硬化剂（A:B）） | 按重量 | 100:30 |
适用时间 [20g at RT] | s | 45-60 |
固化时间[20g at RT] | min | 5-8 |
完全固化[20g at RT] | h | ~ 24 |
硬度 | Shore-oo | 55-80 |
发泡密度 | g/cm3 | 0.2-0.36 |
反应产品颜色 | RAL | 黑色 |
拉伸强度 | N/mm2 | ~ 0.2 |
断裂延伸率 | % | ~ 120 |
应用温度范围(UL50) | ˚C | -30 - +70 ˚C |
耐温性（长期） | ˚C | -40 - +80˚C |
耐温性（短期） | ˚C | -60 - +150˚C |
吸水率 | % | <10 |
物理性能 树脂部分: Bolu Foam BL-1039A
粘度[at 23˚C] | mPa*s | 8000-28,000 |
不加空气密度[at 23˚C] | g/cm3 | 1.05-1.45 |
颜色 | 黑色 |
物理性能 硬化剂部分：Bolu Foam BL-1039B
粘度[at 23˚C] | mPa*s | 70-210 |
密度[at 23˚C] | g/cm3 | 1.17-1.23 |
颜色 | 褐色 |
·加工
在使用之前，A组分树脂需在大桶内均匀混合。
两种原料被设计作为标准剂量和计量装置的双组分聚氨酯使用。最优发泡温度在20 - 25°C。热
处理(加热)加速硬化过程。
表面的粘附力可以通过介质增强 (底涂剂或者物理预处理)或者避免脱模剂。
存储
两个组份原料必须储存在密封容器中。绝对远离水和大气湿度(必要时使用硅胶密封容器)。
存储温度不应超过+ 30°C或低于+ 10°C。
容器在使用后必须立即密封. 打开新桶需要尽快用完，如果注意这些细节，原料可以储藏6个
月。
工业安全
固化剂含有异氰酸酯。它可能刺激皮肤、眼睛和呼吸道,皮肤过敏反应和呼吸道的慢性暴露,也
引发过敏反应。附加信息的安全数据表。请确保工作场所的清洁和良好的通风。保护眼睛和
皮肤。如果意外泼溅在皮肤上,用肥皂水冲洗。如果溅到眼睛里,立即用自来水冲洗10 - 15分
钟,就医。
请注意:
-在大桶上的安全标识和规范要求。
- 聚氨酯生产加工/异氰酸酯 (提供者: Henan Bolu Industrial Co., Ltd, China)
法律免责声明
这份打印文档中详细信息基于我们目前的知识和经验提供，加工者可能不根据我们的的测
试和试验，进行加工和生产，考虑到在测试和使用中可能的影响，只能构成一般的指导方
针。一项具有法律约束力的保证特定属性或是否适合特定的应用不能这样取得。加工者必
须负责任的关注所有权以及现行法律、法规。此数据表代替以前的所有版本。
双组份发泡胶（BL-1039）
Mixing ratio 混合比 resin: hardener | by weight | 100:30 |
Start time 开始乳化时间[10g at 23˚C] | s | 45-60 |
Tack-free time 固化成型时间[10g at 23˚C] | min | 5-8 |
Full hardening 完全固化时间[at 23˚C after] | h | ~24 |
Hardness 硬度 | Shore-00 | 55-80 |
Density of reacted product 密度 | g/cm3 | 0.30-0.36 |
Color of reacted product颜色 | RAL | black |
Tensile strength拉伸强度 | N/mm2 | ~0.2 |
Elongation at break断裂延伸率 | % | ~120 |
Temperature resistance (long-term)长期耐温 | ˚C | -40-+80 |
Temperature resistance (short-term)短期耐温 | ˚C | ~-60-+150 |
Water absorption吸水率 | Weight-% | <10 |
Physical properties resin comp.: BL-1039A
Viscosity粘度[at 23˚C] | mPa*s | 8,000-28,000 |
Density without air loading无空气负荷的密度[at 23˚C] | g/cm3 | 1.05-1.45 |
Color 颜色 | black |
Physical properties hardener comp.: BL-1039B
Viscosity 粘度[at 23˚C] | mPa*s | 70-215 |
Density 密度[at 23˚C] | g/cm3 | 1.17-1.23 |
Color 颜色 | brown |
Processing
Homogenise the resin (A-component) well in the drum before use.
Both materials are designed to use on a standard dosing and metering unit for two component
polyurethane gaskets. The optimum ambient temperature during processing is 20 - 25°C.
Thermal treatment (tempering) accelerates the hardening process. The adhesion to the
substrate can be enhanced by bonding agents (primers or physical pre-treatments) or
prevented by release agents.
Storage
Both components must be stored in tightly sealed containers. Absolutely keep away from
water and atmospheric humidity (use silica gel cartridge if necessary). The storage
temperature should not exceed +30°C or drop below +10°C. The containers must
immediately be resealed after use. Opened drums are to be used up promptly. If these
instructions are observed, the materials are storable at least 6 months.
Industrial safety
The hardener component contains isocyanate. It may cause irritation to the skin, eyes and
respiratory tract, sensibilisation of the skin and respiratory tract as a result of chronic
exposure and also trigger allergic reactions. Additional information is found in the safety
data sheet. Please ensure cleanliness and good ventilation in the workplace. Protect eyes and
skin. Dab off accidental splashes to the skin and remove with soapy water. In case of
splashes into the eyes, immediately rinse under running water for 10-15 minutes and see a
doctor.
Please also take note of:
- the risk phrases and safety phrases on the drums.
Legal disclaimer
The details provided in this printed document are based on our current knowledge and
experience. They do not exempt the processor from conducting his own tests and trials on
account of the abundance of possible influences during the processing and use of our
products and only constitute general guidelines. A legally binding guarantee of specific
properties or suitability for a particular application cannot be derived from such. Possible
proprietary rights as well as laws and regulations in force must always be observed by the
processor on his own responsibility. All previous data sheets cease to be valid with the
publication of this data sheet.
